Technor Langfeldleuchte RMS 540 - 550 und 560 Serie

Charakteristik

Die Technor / Italsmea RMS Leuchten Serie eignet sich hervorragend für On- und Off-Shore-Anwendungen und allen Branchen, wo es eines hohen Korrosionsschutzes bedarf. Gehäuse und Glasrahmen sind aus einem einzigen Blatt Edelstahl AISI304 ohne invasive Montagebohrungen hergestellt, um das Risiko von Wassereintritt durch das Gehäuse zu minimieren.

Außer den Löchern für das Netzkabel, welches durch geeignete Kabelverschraubung (auf Anfrage) geschützt ist, gibt es keine Löcher die von innen nach außen der Leuchte führen. Daher besteht kein Risiko einer Reduzierung der IP-Schutzart, wie es sonst der Fall wäre. Das Design wurde entwickelt um eine Ein-Mann-Montage zu gewährleisten. Eine Person kann sich um Inbetriebnahme oder Wartung, ohne Hilfe und Unterstützung einer weiteren helfenden Hand, kümmern. Durch Verwendung anorganischer Materialien wie Edelstahl und Glas können die RMS Leuchten zu 95% recycelt werden. Nur einzelne komponenten und die Isolierung der Einzelkerndrähte sind etwas pflegebedürftiger

Bildunterschrift

Technical Details

Model RMS 540 RMS 550 RMS 560
Light source RMS series lighting fixtures are suitable for two pins fluorescent lamps G13 socket Philips
TL-D or equivalent (lamps excluded)
RMS series lighting fixtures are suitable for two pins fluorescent lamps G13 socket Philips
TL-D or equivalent (lamps excluded)
RMS series lighting fixtures are suitable for two pins fluorescent lamps G13 socket Philips
TL-D or equivalent (lamps excluded)
Housing AISI304 stainless steel, 0,8mm thickness and transparent part in tempered glass (AISI316L
version available upon request)
AISI304 Stainless steel screws
AISI304 stainless steel, 0,8mm thickness and transparent part in tempered glass (AISI316L
version available upon request)
AISI304 Stainless steel screws
AISI304 stainless steel, 0,8mm thickness and transparent part in tempered glass (AISI316L
version available upon request)
AISI304 Stainless steel screws
IP Rating IP66 IP66 IP66
Emergency Version Available RMS.. lighting fixtures for emergency service of one tube:
- 90 minutes; guarantees 60’ duration with constant flux (emergency lumen factor 18%) and 30’ with decreasing flux
Available RMS.. lighting fixtures for emergency service of one tube:
- 90 minutes; guarantees 60’ duration with constant flux (emergency lumen factor 18%) and 30’ with decreasing flux
Available RMS.. lighting fixtures for emergency service of one tube:
- 90 minutes; guarantees 60’ duration with constant flux (emergency lumen factor 18%) and 30’ with decreasing flux
Ambient temperature -20 °C up to +60 °C -20 °C up to +55 °C -20 °C up to +60 °C
Voltage range 230 Vac 230 Vac 230 Vac
Systempower 1x 18W or 2x 18W or
1x 36W or 2x 36W
1x 18W or 2x 18W or
1x 36W or 2x 36W
1x 18W or 2x 18W or
1x 36W or 2x 36W
Power factor/Cos >0.9 >0.95 >0.95
Ballast Electromechanical ballast with starter and capacitor High frequency electronic ballast conforming with EN 60079 – 15 and IEC 60079 – 15 High frequency electronic ballast conforming with EN 60079 – 15 and IEC 60079 – 15
Gaskets Special cross-section tightness gasket, silicon rubber made (closed cell), located in housing
channel between body and window frame.
Special cross-section tightness gasket, silicon rubber made (closed cell), located in housing
channel between body and window frame.
Special cross-section tightness gasket, silicon rubber made (closed cell), located in housing
channel between body and window frame.
Entries Body complete of two 21mm Ø through holes (on one side) for cable entry, one complete of
metallic plug with M20 locknut and gasket and the other one with temporary plastic plug to prevent dust ingress.
Body complete of two 21mm Ø through holes (on one side) for cable entry, one complete of
metallic plug with M20 locknut and gasket and the other one with temporary plastic plug to prevent dust ingress.
Body complete of two 21mm Ø through holes (on one side) for cable entry, one complete of
metallic plug with M20 locknut and gasket and the other one with temporary plastic plug to prevent dust ingress.

Certificate Details

Model RMS 540 RMS 550 RMS 560
ATEX classification - Group II, Category 2, Gas and Dust Group II, Category 2, Gas and Dust
Area classification - Category 2 (Zone 1 and 21) Category 2 (Zone 1 and 21)
Certificate (ATEX) - INERIS 01ATEX3002X INERIS 01ATEX0060
Certificate (GOST R) - marking upon request, ordering code to be required marking upon request, ordering code to be required
Marking - {ex} II 3 GD
Ex-nA II T(**)
Ex-tD A22 IP66 T(**)
II 2 GD
Ex-de IIC T(**)
Ex-tD A21 IP65 T(**)
** T6/T85°C, T5/T100°C, T4/T135°C
CE Yes Yes Yes
According regulations Compliance with Electromagnetic Compatibility (EMC) according to European Directive
2004/108/CE
Compliance with Electromagnetic Compatibility (EMC) according to European Directive
2004/108/CE
Compliance with Electromagnetic Compatibility (EMC) according to European Directive
2004/108/CE

Optional

Model RMS 540 RMS 550 RMS 560
Pole mounting kit On request On request On request
Ceiling mounting kit On request On request On request
Suspension mounting kit On request On request On request
Wall mounting kit On request On request On request
3°- 4° through holes opposite side On request On request On request
Wiring with High frequency electronic ballast (220-240 V 50-60 Hz) On request Already included Already included